Teledyne O3 Manuel d'utilisateur Page 56
- Page / 114
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Teledyne API Model 401 O
3
Photometric Calibrator Instruction Manual, 01124, Rev. J2
Table 5-1: Test Channel Output
Test # Name Purpose
1
NONE No output
2
O3 DETECT Outputs O
3
detector
3
REF DETECT Outputs IZS ref. det.
4
SAMP PRESS Outputs sample press.
5
SAMP FLOW Outputs sample flow
6
SAMP TEMP Outputs sample temp.
7
ALAMP TEMP Outputs ana lamp temp.
8
O3 FLOW Outputs O
3
flow
9
O3 LAMP TEMP Outputs O
3
lamp temp
10
CHASSIS TEMP Outputs chassis temp
11
DCPS VOLT Outputs DC power
Table 5-2: Diagnostic Tests
Test # Name Type Purpose
1 D/A OUTPUT Analog Tests analog outputs
5.2.1 D/A Output
This test cycles 3 of the analog output channels from 0% to 100% of Full Scale in 20% FS steps.
It starts by outputting 0 volts to all four channels and displaying a 0% button. Then, every five
seconds, the output is increased 20% FS and the button is changed accordingly. Thus, the button
(and the analog outputs) will cycle through the following values:
0%, 20%, 40%, 60%, 80%, 100%, 0%
To pause the output at the current voltage, press the n% button. To resume automatic cycling,
press the n% button again.
5-2
- MODEL 401 1
- CALIBRATOR 1
- SAFETY MESSAGES 2
- TABLE OF CONTENTS 3
- LIST OF FIGURES 7
- LIST OF TABLES 8
- 1 INTRODUCTION 9
- 1.3 Principle Of Operation 10
- 1.3.1 Interferent Rejection 12
- 1.4 Specifications 13
- 1.4.10 Flow Rates 15
- 1.4.11 Power 15
- 1.4.12 Weight 15
- 1.6.1 Electrical Connections 22
- 1.6.2 RS-232 22
- 1.6.3 Pneumatic System 24
- 1.6.5 Output Flow Adjustment 24
- 1.7 Operation Verification 28
- Table 1-1: Test Values 29
- 1.8 Options 30
- 2 OPERATION 31
- 2.1.5 Data Acquisition 32
- 2.1.6 RS-232 Interface 32
- 2.1.7 Password Protection 32
- 2.2 Front Panel 34
- 2.2.3 Status LEDs 39
- 3 CALIBRATION 41
- 3.6 Photometer Calibration 43
- 3.9 Hold Off 45
- 4 SETUP MODE 47
- 4.5 Setting the O 49
- Generation Mode 49
- 4.6 Setting The Time-Of-Day 49
- 4.7 Setting The Date 49
- 4.9 Setting The O 50
- Concentration Range 50
- 4.15 Software Configuration 52
- 0 mV 1000 mV 53
- 5 DIAGNOSTICS 55
- 5.2.1 D/A Output 56
- 6 HANDLING WARNINGS 57
- 7 RS-232 COMMUNICATIONS 59
- 7.1 DAS Reporting 60
- 7.2 Warnings 61
- 7.3 Status/Control 62
- 7.4 Diagnostics 64
- 7.5 Test Measurements 65
- 8 ADJUSTMENTS 69
- 8.4 Flow Readout Adjustment 72
- 8.5 DC Power Supply 74
- 8.6 CPU 74
- 8.7 Status Lines 75
- ± 50 mV 76
- ± 500 mV 76
- 8.12 Bench Feedback Option 78
- 9 TROUBLESHOOTING 79
- 9.2.3 Checking The Keyboard 81
- Table 9-1: Warning Messages 82
- 9.5.5 Cannot Zero 86
- 9.5.6 Cannot Span 86
- Components 87
- 9.6.3 Checking The V/F Card 89
- ° C=2.5V, ± 0.125V/°C 92
- TELEDYNE 96
- 10 ROUTINE MAINTENANCE 97
- 10.2 Leak Checking 98
- 10.3 Cleaning Of Sample Cell 98
- 10.4 Changing The Prom 99
- INTENTIONALLY BLANK 100
- 11 MODEL 401 SPARE PARTS AND 101
- EXPENDABLES KITS 101
- Teledyne API Model 401 O 102
- (table continued) 103
- OPTIONS 105
- Appendix C REFERENCES 109
Produits connexes et manuels pour Mesure, test et contrôle Teledyne O3
(4 pages)
(42 pages)Asko D5434 SOF FS RU Stainless manuales
Manuales del propietario y guías del usuario para Lavaplatos Asko D5434 SOF FS RU Stainless.
Ofrecemos 1 manuales en pdf Asko D5434 SOF FS RU Stainless para descargar gratis por tipos de documentos: Manual de usuario
Commentaires sur ces manuels